- Видео 20
- Просмотров 73 344
Robert Jones
Добавлен 10 окт 2011
Dyson V8 (215681) Battery Disassembly
A brief video I recorded after dismantling my Dyson V8 battery to recover the 186500 cells, apologies I didn't record this as I did it, but as I couldn't see any other videos on RUclips I thought it may help someone else.
Просмотров: 52 485
Видео
Samsung PS60E530 - 60" Plasma TV - No Power
Просмотров 4477 лет назад
The TV would not power on at all, with no standby power/light. I replaced the power board and it now shows a standby light, powers on and seems to be accepting commands from remote control, but shows no screen at all. Any thoughts?
Trianco Eurostar 50/60 Oil Boiler with Problem Firing
Просмотров 10 тыс.7 лет назад
Trianco Eurostar 50/60 Oil Boiler with Problem Firing
Trianco Eurostar 50/60 Won't Fire Up
Просмотров 3,3 тыс.8 лет назад
Trianco Eurostar 50/60 Won't Fire Up
Emyr Wakeboarding on his stag do in Blackpool
Просмотров 6911 лет назад
Emyr Wakeboarding on his stag do in Blackpool
Tractor Pulling - The one with a Tank Engine!
Просмотров 1,1 тыс.11 лет назад
Tractor Pulling - The one with a Tank Engine!
Womens Handball - Great Britain v Montenegro, London Olympics 2012
Просмотров 1,1 тыс.12 лет назад
Womens Handball - Great Britain v Montenegro, London Olympics 2012
'Rookie Bangers' Race at Mendips Raceway on 8th April 2012
Просмотров 1,5 тыс.12 лет назад
'Rookie Bangers' Race at Mendips Raceway on 8th April 2012
Car Tipping in 'Rookie Bangers' Race at Mendips Raceway on 8th April 2012
Просмотров 38712 лет назад
Car Tipping in 'Rookie Bangers' Race at Mendips Raceway on 8th April 2012
'Rookie Bangers' Final at Mendips Raceway on 8th April 2012
Просмотров 30412 лет назад
'Rookie Bangers' Final at Mendips Raceway on 8th April 2012
Hot Rods at Mendips Raceway on 8th April 2012
Просмотров 24512 лет назад
Hot Rods at Mendips Raceway on 8th April 2012
To open, just place shorter end of the battery to the bench vise (with soft jaws) and twist cover open. No need to damage the case with screwdriver. Some clips might be damaged, but you can live with that 🤔
Thank you sir, great
The Dyson INR20700A are 20700 form factor (so not 18650) On ali one can find casings for this Dyson that will hold 21700 batteries. Note: the batteries must have an amperage of 35A or more. The Dyson original batteries have a capacity of 2800mAh while 21700, 35A batteries with a capacity of 4000mAh (43% more) can be found.
Helped a lot! thank you!
Some folks have replaced the weak cell or all cells in this battery pack, though the price of an aftermarket replacement battery pack is reasonably priced.. Thank You
Very useful Thanks.
Thx mate!
Has anyone had any success with the £30 ebay replacement packs? If just replacing individual cells then do they have to be Dyson branded?
I've been using aftermarket batteries on the older DC34, DC35 and V6 for several years now. They've proven to be very good in terms of both reliability and run time. I can especially recommend these brands: Floureon, FlyLinkTech and Flagpower. To replace just the cells you would need high-drain ones but any brand should be fine.
High drain as in 35A or more. 20700 will fit in the Dyson case You can buy cases that will hold 21700 cells. That will give you a much wider choice of batteries and more capacity too.
Great video dude
Gutes Video, greetings from Germany...
Thanks for the video. My two year old original Dyson V8 battery pack still has good capacity, but it’s become slow to recharge. I assume one or more cell became weak and the BMS is doing some balancing each time it’s charged. I suppose there’s nothing to be done except recover all the cells and individually test them for capacity.
Those batteries are not soldered, they are spot welded, DO NOT apply heat to them thinking they are soldered, it may short the cell and cause it to burst
Also, unwise to pull off the metal welded to the cell as it can easily pull holes in the sealed cell. By the way, they are not 18650 but 20700 - bigger !
I’d love to know what tools you think could use to open this without damaging it. I had all these tabs wedged and it still wouldn’t budge a millimeter. Mine was glued closed..
I think you could probably use the plastic tools you use with car panels and mobile phones, just needs to patience 👍
Robert Jones Nope. I’ve dismantled cell phones and gaming systems before. I have pry tools. This was glued inside.
Even harder then, I had no glue! I notice there are heating pads available for removing iPad screens etc, so I guess depending on the type of glue, heat may be an option, but could be it's becoming unserviceable.
Robert Jones yeah pretty much impossible to not break to open. Stinks.
It's a disappointing trend these days with expensive items to prevent repair isn't it!
No problem that you didn't film the actual "breaking it open" , this is very helpfull, thanks!
Nice! I'd like to enter my old corolla in one these. It'd be a fun send off for it.
Good pull.
That's a great start tq.
Why would you need to recover the cells? They are expired-- I missed that.
Why not 😉
Sometimes just one cell has gone bad but in general all batteries would have little life left. I would be careful with using those cells but I’d have no problem to use them for solar powered garden lights for example.
Great video. Just a little correction, joints between batteries are spot welded. So you cannot desolder.
Appreciate that 👍
So if I was to take them apart, what would be the best way to get them back? Can I try to solder them back and hope that it would hold? Or can you recommend something else.
@@aajeev get a spot welder and spot weld it. I am not saying you cannot solder because you can but batteries do not like heat. You need to have a proper preparation and a quick as possible solder solution. Also keep in mind soldering batteries not safe and could be dangerous. Use all PPEs.
@@helel78 thank you. Appreciate you sharing your experience.
:)
Thx for the video. The battery is the 20700 (20mm x 70mm) size not 18650 (18mm x 65mm)
21700....
Thank uou
Faulty coil
sotted up
<3 MONTENEGRO <3 <3 BOJANA POPOVIC <3